| P
9521 Single Axis Position Controller in a calculator sized enclosure Features : Technical Data:
|
 |
| Power Supply: | 230 V AC or 115 |
| Encoder Supply: | 24 V DC / 200 mA, push-pull |
| Input Signals: | PNP (positive logic) |
| Output Signals: | Relay output Normaly Open, 250 V / 3 A |
| Actual Position Memory: | by Li-battery, life: 10 years |
| Connections: | RIA-connector |
| Display: | LED 7 segment red 8 mm high |
| Hardware: | 16 bit-Microprocessor with 32 Kbyte E-Prom and 2 Kbyte RAM |
| System accuracy: | +/- 1 increment |
| Counting frequency: | 20 KHz (higher on request) |
| Enclosure: | Black metal, for fitting into control panel |
| Depth: | 85 mm |
| Cut out: | 66 x 92 mm |
| Ambient temperature: | 0° to +50° C |
| P 8511 / P8721 Single Axis Position Controller without or with programme memory Essential features |
 |
| P8511.PID / P8721.PID: | with PID-analogue output and three
speed operation with external power supply unit NG 13.0 (230 V / 115 V AC) |
| P8511.RP / P8721.RP: | with potential free c/o relay
contacts with integrated power supply (230 V / 115 V AC) |
| Features : Absolute and incremental positioning mode Manual operation Tool offset compensation Quantity counter Encoder pulse monitoring Backlash compensation Pulse multiplication End limit monitoring Tolerance windows "Go-to-datum" routine Fault monitoring 2. Technical Data: |
| Power supply: | + 24 V DC and +10 V DC from ext.
PSU NG 13.0 (PID) 230 V AC / 50 Hz or 115 V AC / 60 Hz (RP) |
| Consumption: | + 24 V DC / max. 600 mA, + 10 V DC / max. 400mA (PID) |
| Encoder supply: | 24 V DC; max. 130 mA |
| Input signal: | NPN or PNP pulse: min. 200 msec input current : max. 10 mA |
| Output signal: | open-collector, PNP (PID) potential free c/o relay contact 250 V / 2 A (RP) |
| Actual position memory: | by NC-Accumulator, life: 5 years |
| Connections: | By D-connectors (PID) by RIA-connectors (RP) |
| Display: | LED-7 Segment red, 8 mm high |
| Hardware: | 8-bit-microprocessor with 32 Kbyte E-Prom |
| Counting frequency: | 10 KHz (higher on request) |
| Enclosure: | black metal, for fitting into control panel |
| Dimensions: | width x height x depth: 144 x 144
x 55 mm (PID) 144 x 140 x 90 mm (RP) |
| Cut out: | 138 x 138 mm |
| Ambient temperature: | 0 ° to + 50 ° C |
| P 99 1 to 4-Axis- Position Controller with screen Essential features |
 |
| The 99 controller enables low cost
control up to 4 axis to be effected. Simple operation and precise
customer requirements can be configured, using the high definition
LCD screen and keypad. Data communications with PC, PLC and Printer are possible by
means of three simultaneous ports. Machine specific auxiliary functions are no problem as they are
integrated in the extensive standard software package. Technical Data |
| Power supply: | + 24 V DC +/- 10 % |
| Consumption: | + 24 V / max. 600 mA |
| Encoder supply: | 24 V DC; 130 mA |
| Input signals: | PNP, min. 200 msec, max. 10 mA |
| Output signals: | push-pull, short circuit
protected, output current: max. 30 mA /output |
| Memory: | by Novram |
| Display: | Screen, dimensions:122x 66
mm 240x128 pixels |
| Hardware: | 16 bit microprocessor with 128 Kbyte E-Prom and 128 Kbyte RAM |
| System accuracy: | + / - 1 increment |
| Counting speed: | up to 300 m/min (resolution 0,1 mm) |
| Enclosure: | black metal, for fitting into control panel |
| Dimensions: | width : 288 mm height: 144 mm depth : 46 mm (allow another 45 mm for connectors) |
| Cut out: | 282 mm x 138 mm |